The Definitive Guide to Fishing with a Wacky Worm Rig
Fishing for bass is a lot of fun since everyone has a different “secret method.” Freshwater gamefish are voracious eaters of a wide variety of prey, therefore a variety of fishing setups may be used to catch them. Many types of rigs, such as Texas Rigs and Carolina Rigs, attempt to imitate the motion of the prey that bass consume.
Wacky Worm Rigs will be explained in detail, including how to tie them, how to fish them, and which gear is ideal for utilizing them.
The bass at your favorite spot will be slain by your Wacky Worm Rig after reading this post.
What the Heck is a Wacky Worm Rig?
Wacky Worm Rigs are made of classic rubber worms with a hook in the middle.
The worm seems to have been caught by mistake. However, the motion and weedless possibilities of the Wacky Worm Rig are what really set it apart.
It’s possible to rig up a Wacky Worm Rig without any additional steps, but more experienced anglers like to strengthen the worm where the hook penetrates the worm.
Rubber bands, O-rings, and fishing line may all be used to stop the hook from ripping a worm too early on.
Making a Wacky Worm Rig: Step by Step Instructions
A real Wacky Worm Rig can only be built in a precise way.
To begin, thread a hook through your line. Hook makers have begun producing hooks exclusively for the Wacky Worm rig, which has been around for a long time. You may use any hook that has a circular shape and a weed guard if you can’t locate one specifically labeled for Wacky Worm Rigs. If you’re fishing in an area with a lot of vegetation, a weed guard may come in handy.
1-Leave approximately half an inch of the hook exposed on the opposite side of the plastic lure once you’ve hooked it through the center. Rubber bait, such as the Senko worm, is a wonderful choice for lures. Rubber frogs, and even squid or mice may be be used. It’s important to hook them in the center!
2- Be sure to place an o-ring or little rubber band around the worm where the hook is if you want it to last longer. In order to attract fish, you may use this to bolster the worm’s support system while it’s being jerked .
3- When fishing the rig, you may either put a split shot weight near the hook or a few feet up the line, depending on how you want to fish. The lift and drop and crawl and drag techniques will benefit from this, since it speeds up the process of getting your rig to the bottom.
Wacky Worm Tackle
Rod:
Wacky Worm fishing requires a certain style of rod and reel depending on the species of fish you want to catch.
As far as fishing rods go, be sure they can handle 10 lb. line and up to 15 lbs. of drag. Medium-to-heavy power rods are preferred by most fishermen because of the added strength they give while fighting a bass to the surface.
You don’t want the bass to get your line tangled up in grass or submerged logs. You should also take into account the rod’s tip speed. When fishing bass, it is best to lean to the fast side in order to stand up to a battle with a large, powerful fish.
Fishing Line Types
Monofilament or fluorocarbon, should be used in clear water not much vegetation. Weed and structure fishing are best done using fluorocarbon lines.
Debris won’t damage braided lines, but they’re vulnerable to tearing. There is very little stretch in braided and fluorocarbon lines, which means that you can readily detect the slightest touch of a bass on your Wacky Worm Rig.
Wacky Worm Rig Fishing Techniques
When it comes to the Wacky Worm Rig, a lot of what’s been learned about the Texas Rig and Carolina Rig also applies.
The Lift and Drop
It is advisable to use the Lift and Drop approach in places with little shelter. The Wacky Worm Rig’s activity is more likely to become tangled up in obstructions.
1. In order to catch a fish, cast your bait in the direction to where you believe they are hiding.
2. Allow the Wacky Worm Rig to sink to the bottom before continuing.
3. You should keep your rod tip aimed towards the rig, and take up in any excess line by reeling in a bit.
4. In order to get the bait to move, gently yank the rod tip up 6 to 12 inches to move the bait off the bottom.
5. Allow the rig to rest back to the bottom for a few seconds, then repeat the process.
6. You should experiment with various speeds and discover what the fish prefer.
7. When the bait is dropping back to the bottom, bass often attack it. If you sense anything out of the ordinary, give your fishing pole a jerk!
Crawl and Drag
This technique works well in all kinds of water, even when there is a lot of underwater cover.
1. If you believe the fish are lurking in a certain area, cast your lure there.
2. Allow the Wacky Worm Rig to sink as far as it can.
3. You should keep your rod tip aimed towards the rig, and take up any excess line with the reel.
4. Allow the Wacky Worm Rig to crawl around the bottom by slowly lifting your rod.
5. As soon as you’ve raised the rod 6 inches to a foot, drop it back down and take up the slack in the fishing line again.
6. Repeat after allowing the Wacky Worm Rig to rest for a second on the bottom.
7. To observe what the fish prefer, experiment with various speeds of the action.
8. Give your line a short jolt if you sense a touch on it. The bass will be on if it’s there!
The Swimming Retrieve
The greatest time to employ the Swimming Retrieve is in the spring and autumn, when bass are searching for food.
1. The first thing to do is to cast your bait in the direction of where you believe the fish are lurking.
2. Slowly lower the bait into the water for a few moments. Start reeling in the Wacky Worm Rig before it hits the bottom.
3. Adjust your reeling speed to keep the bait swimming close to the bottom
You may even yank the rod a few times to mimic an injured fish.
4. To resemble a wounded animal, you might twitch the rod every now and again.
5. To set the hook, if you feel somethng on your line, give it a fast jerk.
See also Best Kayaks for Fishing .